Vehicle identification number: 0603077
VW T5 1.9 TDI Suspension arm (105 hp Diesel AXB)
-
- Vehicle Identification Number (VIN) to: 7H-BH500 000, 7H-BX500 000
- Gross vehicle weight [kg]: 2600, 2800, 2850, 3000
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- Supplementary Info: Original VAICO Quality
- Fitting Position: Lower Right, Front Axle
- paired article number: V10-0683
- Axle alignment required after fitting
- Article number of the recommended special tool: V99-1020
- Packaging width [cm]: 6,1
- Packaging height [cm]: 42,4
- Packaging Depth [cm]: 41,1
- Item number: V10-0684
- Manufacturer: VAICO
- EAN number: 4046001360718
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
- Fitting Position: Front Axle Right
- Vehicle type: 2.6T / 3.0T
- paired article number: TC1488
-
- Fitting Position: Front Axle Right, outer
- for PR number: 0WL, 0WM, 0WN, 0WQ, 1BA, 1BB, 1BJ, 2MD, 2MF, 2MG, 2MK, 2ML
- Control / Trailing Arm Type: Control Arm
- Material: Steel
- Fitting Position: Right, Lower
- Length [mm]: 410
- Height [mm]: 110
- paired article number: TC1488
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Width [mm]: 410
- Item number: TC1489
- Manufacturer: DELPHI
- EAN number: 5012759385487
- Condition: New
-
- Fitting Position: Front Axle Left, Lower
- Special Purpose Vehicle: for special-purpose vehicles
- for PR number: 0E0-2MR, 0E0-2MT, 0E0-2MU
- Control / Trailing Arm Type: Control Arm
- paired article number: VO-TC-13776
- Supplementary Article / Supplementary Info Info 2: with rubber mount, without ball joint
- reinforced version
- Packing Type: Box
- Article number of recommended accessories: VO-BJ-7050
- Packaging length [cm]: 51
- Packaging width [cm]: 44,5
- Packaging height [cm]: 15
- Item number: VO-TC-13775
- Manufacturer: MOOG
- EAN number: 4044197923113
- Condition: New
-
- Fitting Position: Front Axle Left
- Vehicle type: 2.6T / 3.0T
- paired article number: TC1489
-
- Fitting Position: Front Axle Left, outer
- for PR number: 0WL, 0WM, 0WN, 0WQ, 1BA, 1BB, 1BJ, 2MD, 2MF, 2MG, 2MK, 2ML
- Control / Trailing Arm Type: Control Arm
- Material: Steel
- Fitting Position: Left, Lower
- Length [mm]: 410
- Height [mm]: 110
- paired article number: TC1489
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Width [mm]: 410
- Item number: TC1488
- Manufacturer: DELPHI
- EAN number: 5012759385470
- Condition: New
- Control / Trailing Arm Type: Control Arm
- Fitting Position: Front Axle Left
- paired article number: 49398956
- Vehicle configuration line / variant: MAX 2.6T - 3.0T
- Item number: 49398938
- Manufacturer: CORTECO
- EAN number: 3358960635556
- Condition: New
-
- Fitting Position: Front Axle Right
- Vehicle Identification Number (VIN) to: 7H...C...000000
- not for gross vehicle weight [kg]: 3200
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- paired article number: 821 0812 10
- Item number: 821 0811 10
- Manufacturer: FAG
- EAN number: 4014870414191
- Condition: New
- Control / Trailing Arm Type: Control Arm
- Material: Cast Iron
- Cone Size [mm]: 21,5
- Fitting Position: Lower, Front Axle Left
- paired article number: 63679
- Vehicle configuration line / variant: MAX 2.6T - 3.0T
- Rod / Strut: Push Rod
- Item number: 63678
- Manufacturer: SIDEM
- EAN number: 5413978169597
- Condition: New
price incl. 19% VAT
excl. delivery costs
- Control / Trailing Arm Type: Control Arm
- Material: Cast Iron
- Cone Size [mm]: 21,5
- Fitting Position: Lower, Front Axle Right
- paired article number: 63678
- Vehicle configuration line / variant: MAX 2.6T - 3.0T
- Rod / Strut: Push Rod
- Item number: 63679
- Manufacturer: SIDEM
- EAN number: 5413978169603
- Condition: New
price incl. 19% VAT
excl. delivery costs
-
- Fitting Position: Front Axle Left, outer, Lower
- for PR number: 0WL, 0WM, 0WN, 0WQ, 1BA, 1BB, 1BJ, 2MD, 2MF, 2MG, 2MK, 2ML
- Control / Trailing Arm Type: Control Arm
- paired article number: SCA-10225
- Item number: SCA-10224
- Manufacturer: KAVO PARTS
- EAN number: 2220122290429
- Condition: New
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- Supplementary Info: Original VAICO Quality
- Fitting Position: Lower Left, Front Axle
- paired article number: V10-9791
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Weight [kg]: 9
- Axle alignment required after fitting
- Article number of the recommended special tool: V99-1020
- Packaging width [cm]: 55
- Packaging height [cm]: 11
- Packaging Depth [cm]: 40
- Item number: V10-9790
- Manufacturer: VAICO
- EAN number: 4046001475764
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Control / Trailing Arm Type: Control Arm
- Supplementary Info: Original VAICO Quality
- Fitting Position: Lower Right, Front Axle
- paired article number: V10-9790
- Weight [kg]: 9
- not for PR number: 0WR
- Axle alignment required after fitting
- Article number of the recommended special tool: V99-1020
- Packaging width [cm]: 55
- Packaging height [cm]: 11
- Packaging Depth [cm]: 40
- Item number: V10-9791
- Manufacturer: VAICO
- EAN number: 4046001475634
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
- Gross vehicle weight [kg]: 2600, 3000, 2850, 2800
- Fitting Position: Front Axle Left
- Control / Trailing Arm Type: Control Arm
- paired article number: VKDS 321037
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Control / Trailing Arm Design: Triangular Control Arm
- Item number: VKDS 321036
- Manufacturer: SKF
- EAN number: 7316577895493
- Condition: New
price incl. 19% VAT
excl. delivery costs
- Control / Trailing Arm Type: Control Arm
- Fitting Position: Front Axle Right
- Item number: 301181310680
- Manufacturer: MAGNETI MARELLI
- EAN number: 8001063966410
- Condition: New
- Control / Trailing Arm Type: Control Arm
- for PR number: 1BA, 1BB, 1BJ, 2MD, 2MF, 2MG, 2MK, 2ML
- Fitting Position: Front Axle Right
- paired article number: 58006201
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Item number: 58006102
- Manufacturer: METZGER
- EAN number: 4250032435783
- Condition: New
- Control / Trailing Arm Type: Control Arm
- for PR number: 1BA, 1BB, 1BJ, 2MD, 2MF, 2MG, 2MK, 2ML
- Fitting Position: Front Axle Left, Front Axle Right, Left
- paired article number: 58006102
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Item number: 58006201
- Manufacturer: METZGER
- EAN number: 4250032435790
- Condition: New
-
- Gross vehicle weight [kg]: 2850, 2800, 3000, 2600
- Fitting Position: Front Axle Right
- Control / Trailing Arm Type: Control Arm
- paired article number: VKDS 321036
- Supplementary Article / Supplementary Info Info 2: without ball joint
- Control / Trailing Arm Design: Triangular Control Arm
- Item number: VKDS 321037
- Manufacturer: SKF
- EAN number: 7316577895516
- Condition: New
price incl. 19% VAT
excl. delivery costs
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- Fitting Position: Front Axle Left, Lower
- paired article number: 30 93 8284
- Supplementary Article / Supplementary Info: with rubber mounts
- not for PR number: 0WR
- not for OE number: 7H8 407 151 B
- Item number: 30 93 8285
- Manufacturer: SWAG
- EAN number: 4044688655851
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
price incl. 19% VAT
excl. delivery costs
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- Fitting Position: Front Axle Right, Lower
- paired article number: 30 93 8285
- Supplementary Article / Supplementary Info: with rubber mounts
- not for PR number: 0WR
- not for OE number: 7H8 407 152 B
- Item number: 30 93 8284
- Manufacturer: SWAG
- EAN number: 4044688655844
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
-
- Fitting Position: Front Axle, Right
- for PR number: 1BA, 1BB, 1BC, 1BJ, 2HD, 2MF, 2MG, 2MH, 2ML
- Control / Trailing Arm Type: Control Arm
- paired article number: VO-WP-2316
- Supplementary Article / Supplementary Info Info 2: with rubber mount, without ball joint
- Packing Type: Box
- Article number of recommended accessories: VO-BJ-1990
- Packaging length [cm]: 51
- Packaging width [cm]: 44,5
- Packaging height [cm]: 15
- Item number: VO-WP-2317
- Manufacturer: MOOG
- EAN number: 4044197334582
- Condition: New
- Control / Trailing Arm Type: Control Arm
- Material: Cast Steel
- Fitting Position: Front Axle Left, Lower
- paired article number: 38284
- Weight [kg]: 8,405
- Supplementary Article / Supplementary Info: with rubber mounts
- not for PR number: 0WR
- Observe service information
- not for OE number: 7H8 407 151 B
- Item number: 38285
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816382850
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
price incl. 19% VAT
excl. delivery costs
- 1
- 2
- 3
- 4
- 5